Led It!

Minecraft 版本： 1.21.1

平台： neoforge

标签： decoration utility

LED It！

English | 中文

English

LEDIt connects your Minecraft world to WLED devices, transforming your room's lighting into an ambient extension of the game. Walk through biomes, take damage, earn achievements — your LED strip follows along.

Features

• Biome-reactive lighting — LEDs shift color based on the biome you're standing in (forest green, desert amber, ocean teal, nether crimson...)
• Smooth biome transitions — Colors blend gradually (configurable duration) when moving between biomes
• Health-based breathing — LED brightness pulses with your health; low HP causes faster breathing and a red hue shift
• Damage flash — Instant bright red flash on hit, fading back over ~1.5 seconds
• Fire effect — Rapid orange flicker while burning
• Cave detection — Deep blue-indigo tones when underground (Y < 50)
• Death effect — Dark crimson while on the death screen
• Achievement celebrations — Per-type effects: green for Tasks, gold for Goals, purple for Challenges
• Ambient light response — LEDs dim at night, in caves, or during thunderstorms
• Time-based frame scheduling — Configurable 1–1000 FPS, independent of game tick rate
• Dual transport — JSON HTTP API (simple) or E1.31/sACN over UDP (high performance)

Setup

1. Install the mod and all dependencies
2. Launch Minecraft and go to Mods → LEDIt → Config (the gear icon)
3. Configure your WLED device:
   • WLED Device Address: IP or hostname of your WLED controller
   • WLED Port: HTTP port (default 80)
   • LED Count: Number of LEDs on your strip
   • Target FPS: Updates per second (default 2; with E1.31 you can go much higher)
   • Brightness: Master brightness (0–255)
   • Transition Time: How long biome color blends take (in ticks)

Using E1.31

E1.31/sACN sends raw DMX data over UDP, avoiding HTTP overhead. For smooth high-FPS updates:

1. In the mod config → Transport tab, enable Use E1.31 (sACN)
2. Set E1.31 Port (default 5568) and Universe (default 1)
3. In WLED web UI → Config → Sync Interfaces:
   • Enable Network DMX input
   • Type: E1.31 (sACN)
   • DMX Mode: Multiple RGB
   • Multicast: OFF
   • Start Universe: 1
   • DMX Start Address: 1
   • Save & Reboot

Effect Priority

Effects are layered with the following priority (higher = overrides lower):

Death Screen → Damage Flash → Achievement → Fire → Cave → Biome

Configuration

中文

LEDIt 将 Minecraft 世界与 WLED 设备连接起来，让你房间的灯带成为游戏的氛围延伸。穿梭群系、受到伤害、获得成就——LED 灯带都会随之变化。

功能

• 群系响应 — LED 根据所在群系变换颜色（森林翠绿、沙漠琥珀、海洋青蓝、下界猩红...）
• 平滑过渡 — 群系切换时颜色渐变过渡（时长可配置）
• 血量呼吸 — LED 亮度随血量脉动；低血量时呼吸加快、色调偏红
• 受伤闪红 — 受到伤害瞬间全红，约 1.5 秒淡出
• 着火特效 — 燃烧时橙红色快速闪烁
• 洞穴检测 — 地下（Y < 50 且不露天）切换深蓝靛色
• 死亡效果 — 死亡界面显示暗红色
• 成就庆祝 — 按类型区分：普通任务绿色、目标金色、挑战紫色
• 环境光响应 — 夜晚、洞穴、雷暴时灯带自动变暗
• 时间驱动帧率 — 1–1000 FPS 可调，独立于游戏 tick
• 双传输模式 — JSON HTTP API（简易）或 E1.31/sACN UDP（高性能）

使用方法

1. 安装模组和所有依赖
2. 启动游戏，进入 Mods → LEDIt → Config（齿轮图标）
3. 配置 WLED 设备：
   • WLED 设备地址：WLED 控制器的 IP 或主机名
   • WLED 端口：HTTP 端口（默认 80）
   • LED 数量：灯带 LED 数量
   • 目标 FPS：每秒更新次数（默认 2；配合 E1.31 可设更高）
   • 亮度：主亮度（0–255）
   • 过渡时间：群系颜色过渡时长（tick 数，20 tick = 1 秒）

E1.31 设置

E1.31/sACN 通过 UDP 直接发送 DMX 数据，无 HTTP 开销，可实现流畅高帧率：

1. 模组配置 → Transport 标签 → 开启 Use E1.31 (sACN)
2. 设置 E1.31 端口（默认 5568）和 Universe（默认 1）
3. WLED 网页界面 → Config → Sync Interfaces：
   • 启用 Network DMX input
   • Type：E1.31 (sACN)
   • DMX Mode：Multiple RGB
   • Multicast：关闭
   • Start Universe：1
   • DMX Start Address：1
   • 保存并重启

效果优先级

效果按以下优先级叠加（越高越优先）：

死亡界面 → 受伤闪红 → 成就 → 着火 → 洞穴 → 群系

配置参考